iMixie.com
Website to compare Indian Mixer Grinders

How to open a stuck jar of Mixer Grinder, Blender Mixie blade jammed and not turning

Jammed stuck mixie mixer grinder blade is a common problem and it happens when the seal in the bearing of the blender mixer blades leaks and salty water from the food from seeps into the bearing of the mixie blades causing it to corrode and get jammed. The mixer will stop working under these conditions. The best solution is to take it to the nearest service center of the Mixer Grinder to clean the bearings, which they may do free or replace the complete blade with new bearings. You can try some emergency repair procedures on the mixer grinder before taking the trouble of visiting the mixer grinder service center as explained below.


For emergency repairs keep the mixie mixer grinder jar upside down and pour some cooking oil into the space where the motor coupler is. Pour just enough oil to keep the level of oil to below the rubber or plastic motor coupler. Leave aside for a few minutes and then twist the rubber or plastic motor coupler with the help of a plier or similar hand tools. The first few turns will be very tight, but once it starts turning a few times it will loosen up. While doing this the jar should be upside down with a little oil under the rubber plastic motor coupling to lubricate the mixie mixer grinder jar blades.

Once the jar blade moves freely, you can put it on the Motor base and run it empty for a few seconds at a time, till the mixer jar blade runs freely. You can use penetrating lubricants like WD40 instead of cooking oil and it will work faster. After the mixie jar has loosened you must first mix some water alone and throw it off. This is to clean the jar.

To prevent Mixer jar blades from getting stuck, it is a good practice to put some fresh water in the jar and run it for a few seconds and throw away this water. Try your best not to wet the outside bottom of the mixer grinder jar where the mixer coupler is. Keep the blender jar upside down to allow water to drain away from the bearings.

When you have finished doing your grinding jobs for the day, the best way to clean the insides of the Mixie jar is to pour about a cupful of clean water from your water purifier into the mixer jar and then put it on the mixer motor and run it for about 10 seconds. This will make the insides of the mixer jar easier to clean. It is always a good practice to clean mixer jars immediately on finishing any grinding jobs. When cleaning the outside of the mixer jar make sure that you do not let water come in contact with the mixer jar motor coupling at the base of the mixer jar. Always twist the rubber coupler at the bottom of the jar to make sure it turns freely.


How to clean mixer grinder

As mentioned before, it is a good habit to put some plain water in the mixer grinder jar and run it on the mixer motor whenever you finish a mixer grinding job.

To clean the body of the mixer motor, the first thing to do is to pull out the electrical plug of the mixer motor and not to use the mixer for about half an hour to allow any water that has seeped into the speed controller of the mixer jar motor. Only use damp cloth to wipe the mixe motor base and then again wipe with a dry cloth.

Never ever spray cleaning solutions on the mixer motor base, because these strong detergent based cleaning liquids could seep into the electrical switch of the mixer motor and cause electrical short. Also it is better not to use detergents like Vim liquid or others to clean the body of the mixer motor.

Mixer Grinder overload protector, why Mixer Grinder stops while working

Sometimes the mixer grinder stops when doing tough grinding jobs, this is because mixer motor gets too hot and mixer grinder safety switch cuts off the power supply to the mixer motor.

When this happens, the first thing to do is make sure that the power cord of the mixer is pulled out of its plug socket, then you have to turn the mixie motor upside down and press the red overload safety switch under the mixer grinder motor. Most of the time you have to wait a few minutes for the motor to cool down before the thermal safety switch will switch on. Once the mixer grinder safety switch engages and you can press it on, it is a good idea to run the mixie without any load for about 30 seconds to further cool the mixer grinder motor.


Overload conditions of a mixer grinder happens when you try to do the mixing job quickly by putting too much material in the mixer grinder jar or the material is too thick for the mixie to handle or may be, the speed of the mixer grinder is too high. Try to overcome these problems by reducing the amount of material in the jar by half and doing the grinding two times. If the material was too thick, then add some water, if your recipe allows for a thinner mixture.

Allow Air in the Mixer Grinder Jar to Escape

When you close the lid of a mixie jar, the air inside of the jar gets compressed. When you start the mixer grinder this air gets even more compressed. If the contents in the mixer jar is hot, then it is even worse. Thus there is always the tendency for the lid to blow out or gets open and the contents of the jar may get splashed all over your kitchen to make a real mess and for you a major cleaning job.

To avoid this, normally the mixer jar lid has a small air vent, make sure that it is not blocked. Do not start the mixer grinder immediately on closing, but wait about 5 seconds to give the compressed air a chance to escape.

Normally there is a small cap at the top of the jar lid cover. When you are starting the mixie, remove this cap and hold it loosely over the cap opening so that the contents will not spill over, but will allow the air which gets pressurised when you start the mixie, to escape. This will avoid the mess of a jar blow out.

How to use Indian Mixer Grinder in USA 110 Volts 60Hz.

For an Indian Mixer grinder to work in USA 110 volts will require a step-up transformer to convert the US 110volts current to Indian 220-240 volts. Since the more powerful mixer grinders in India are the 750 Watts type, like the Preethi Blue leaf range, it is better to get a step up transformer with a slightly higher rating, say a minimum of 1000 watts range like this 110V to 220V, capacity 1000 Watts, step-up (or down) transformer from Amazon.com for about $51 or this cheaper model 750 watts step-up transformer, 110 Volts to 220 Volts, from Amazon for about $39-.

The Electric Frequency in the US is 60 Hz or Cycles per second instead of the 50Hz in India. So the Indian mixer grinder in USA will run at a higher speed. The Indian mixer grinders are designed for rough and tough working conditions in India and not to fail in the frequent Voltage Fluctuations in India. To compensate for this 20% increase in speed when Indian Mixer and grinders work in USA, make sure you do not run this Indian Electrical 220V 50Hz appliances at full speed in the USA with 60 cycle electricity. Indian Electrical appliances are built sturdy for withstand unreliable Indian electric voltages and will not easily get damaged in USA, especially since all top of the range Indian Mixer and grinders have built-in overload protection.


Your best source to buy Indian Mixer Grinder locally

Please find below links to the Amazon online store in your country. Amazon is usually your best place to buy Indian Mixer Grinders because not only are they very competitively priced but you also have the assurance of service, and in the worst case, even return for a refund in case you are not satisfied.

This is the Link for Indian Mixer Grinders on Amazon Canada

This is the Link for Mixer Grinders (both 220V and US 110V) on Amazon India

This is the link for Indian Mixer Grinder on Amazon UK

This is the link for 110V 60Hz Indian Mixer Grinders on Amazon USA



All pages in our website www.iMixie.com

Below are links to all the pages on this website. Please visit these pages and make full use of all the great information about Indian Mixer Grinders and Wet Grinders.